How To Install Exhaust Spring Bolts
As an Amazon Associate, we earn from qualifying purchases.
Installing exhaust spring bolts is a relatively easy process that can be completed in a few minutes with the proper tools. The most important thing to remember when installing exhaust spring bolts is to make sure that the threads are clean and free of debris before starting. This will ensure that the bolts install smoothly and without issue.
- Park your vehicle on a level surface and place jack stands under the frame to support it while you work
- Locate the exhaust system hanger closest to the front of the vehicle and remove it by unscrewing the bolt that holds it in place with a socket wrench
- Insert the end of a long screwdriver or pry bar into one of the holes in the hanger bracket and push downward to release the tension on the exhaust pipe so you can slide it out of the bracket
- Do not allow too much slack in the exhaust pipe or it may fall and cause injury
- Unbolt the flange at the rear of the catalytic converter or muffler from its mounting brackets using a socket wrench, then slide it forward to expose the bolts holding the spring in place
- Remove each bolt holding the spring in place, then pull out the old spring and discard it
- Install the new spring by slipping it over the exhaust pipe, then threading and tightening each bolt by hand before torqueing them to specifications using a torque wrench
Table of Contents
Exhaust Spring Bolts How Tight
If you’re like most people, you probably don’t think too much about the exhaust system on your vehicle. But if you’re a car enthusiast, you know that the exhaust system is one of the most important parts of the car. The exhaust system includes the muffler, catalytic converter, and other parts that help to reduce noise and emissions.
One of the most important parts of the exhaust system are the exhaust spring bolts.
Most cars have four or five bolts that hold the muffler and catalytic converter in place. These bolts are critical for keeping your exhaust components secure.
If even one of these bolts becomes loose, it can cause serious problems. Not only will your car make more noise, but it could also lead to expensive repairs.
So how tight should these bolts be?
The answer depends on your specific vehicle. Consult your owner’s manual or ask a mechanic for guidance on what torque setting to use when tightening these bolts. In general, though, you should aim for around 15-20 ft-lbs of torque.
Be careful not to overtighten the bolts, as this could damage them or strip the threads.
Once you’ve tightened all of the exhaust spring bolts on your car, keep an eye on them and check them periodically to make sure they haven’t loosened up over time. With proper care and maintenance, your exhaust system will last for years to come!
How Do You Install Spring Bolts?
To install spring bolts, you’ll need a few tools and supplies. First, gather your materials. You’ll need a drill, a screwdriver, some screws, washers and nuts, and your spring bolts.
Spring bolts come in different sizes, so make sure you get the right size for your project.
The size of the pilot hole will depend on the size of the screw you’re using. Once the pilot hole is drilled, insert the screw into it and tighten with a screwdriver until snug. Now it’s time to attach the springs.
Place a washer over each end of the spring bolt, then thread on a nut. Use your wrench to tighten each nut until secure. That’s it!
Your spring bolt is now installed and ready to use.
How Do You Tighten Spring Bolts on Exhaust?
If your car has a spring bolt on the exhaust, you’ll need to know how to tighten it. The process is actually quite simple and only requires a few tools.
First, you’ll need a socket wrench that fits the bolt.
You may also need a ratchet if the bolt is tight. Once you have the right tool, simply turn the bolt clockwise to tighten it.
It’s important not to over-tighten the bolt, as this can damage the exhaust system.
If you’re unsure of how tight to make it, consult a professional mechanic. With just a little effort, you can easily tighten a spring bolt on your exhaust!
How Do You Install Exhaust Bolts?
Installing exhaust bolts is a simple process that can be done in a few minutes with the right tools. The first step is to identify the location of the bolt holes on the vehicle. Next, use a drill bit to create pilot holes in the locations identified.
Once the pilot holes are created, insert the exhaust bolts into the holes and tighten them using a wrench or socket. Be sure to check for leaks after installation and retighten if necessary.
What are the Springs for on Exhaust Bolts?
The springs on exhaust bolts are there to provide a snug fit and prevent the bolts from loosening over time. Over time, vibrations from the engine can cause bolts to loosen, which can lead to exhaust leaks. The springs help keep the bolts tight and prevent exhaust leaks.
How to Replace Exhaust System on a 04-09 Subaru Outback
Conclusion
It’s easy to install exhaust spring bolts! Just follow these simple steps:
1. Attach the exhaust pipe to the header using a U-bolt clamp.
Make sure the bolt is tight.
2. Suspend the muffler from the bracket using an S-hook.
3. Connect the tailpipe to the muffler using a band clamp.
Again, make sure this connection is tight.
4. Insert the exhaust springs into their respective hangers on either side of the vehicle. If you have difficulty getting them started, use a small amount of WD-40 or other lubricant on the threads to help get them going.
Be careful not to overtighten these bolts!